MR Soft - SimplyCam, SimplyLaser and SimplyLathe Trial version
Note:
- You can download the trial version or login in the Customer Area to download the full version if you are a registered customer.
- The registered user, receive automatic email to advised for new important updates.
- Free Trial Limitation:
Drawing cannot be saved in Dxf
Only up to 100 lines of G-Code are generated
SimplyCam 3.66 Trial version (Note: the G-Code generated is limited to approximately 100 lines)
This release is the current development version. Please verify regularly new updates.
To install the program, download and unzip the SimplyCam3.zip file on a temp directory.
Please use Winzip or another recent utility.
Run "setup-simplycam3.exe" to start the installation process.
Click here to start downloading SimplyCam3.zip - (File Size: 1.77MB)
SimplyLaser 3.66 Trial version (Note: the G-Code generated is limited to approximately 100 lines)
This release is the current development version. Please verify regularly new updates.
To install the program, download and unzip the SimplyLaser3.zip file on a temp directory.
Please use Winzip or another recent utility.
Run "setup-simplylaser3.exe" to start the installation process.
Click here to start downloading SimplyLaser3.zip - (File Size: 1.77MB)
SimplyLathe 3.49 Trial version (Note: the G-Code generated is limited to approximately 100 lines)
Note: No further development. SimplyLathe module will no longer be updated and supported.
To install the program, download and unzip the SimplyLathe3.zip file on a temp directory.
Please use Winzip or another recent utility.
Run "setup-simplylathe3.exe" to start the installation process.
Click here to start downloading SimplyLathe3.zip - (File Size: 1.77MB)
SimplyCam Release History
To get the exact version number (or compiled release version) of the SimplyCam application on your computer, click About from the Help menu.
- 3.6.6.3: released on February 01, 2020
Fixed many small bugs
- 3.6.6.0: released on January 24, 2020
Fixed many small bugs
- 3.6.5.0: released on November 05, 2019
Fixed many small bugs
- 3.6.0.0: released on July 30, 2019
Added Merge Snc file
Added Retract Plane in mill toolpaths
Fixed pocket toolpath
Fixed postprocessor vars
Fixed many small bugs
- 3.5.0.0: released on November 15, 2018
Fixed many small bugs
- 3.4.9.0: released on May 15, 2018
Fixed many small bugs
- 3.4.0.0: released on November 15, 2017
Fixed Svg parsing
Fixed some small bugs
- 3.3.9.0: released on September 06, 2017
Added toolpath to Geo/Dxf funcion
Added Comments operations
Fixed Write operation in Laser module
Fixed some small bugs
- 3.3.8.0: released on July 19, 2017
Added Laser Pocket toolpath
Fixed some small bugs
- 3.3.6.0: released on February 14, 2017
Fixed some small bugs
- 3.3.5.0: released on January 22, 2017
Fixed dxf read lwpolyline
Fixed some small bugs
- 3.3.0.0: released on July 16, 2016
Added Write toolpath
Fixed some small bugs
- 3.2.0.0: released on April 19, 2016
Added GRBL Panel
Added Solid Simulator
Separate module management Mill, Laser, Lathe
Added TrueType UTF8 management
Added line-width of toolpath
Fixed zig zag Pocket toolpath
Fixed Drag/Drop operations
Fixed crash on Simulation
Fixed some small bugs
- 3.0.6.0: released on August 08, 2015
Fixed open Contour toolpath
Fixed crash on Simulation
Fixed some small bugs
- 3.0.5.0: released on July 26, 2015
Added Help
Fixed Lathe Finish toolpath
Fixed some small bugs
- 3.0.3.0: released on June 19, 2015
Added Lathe Rough and Lathe Finish toolpath
Fixed Vectorize function
Fixed editing entities in Treeview
Fixed some small bugs
- 3.0.1.0: released on April 07, 2015
- 2.4.0.0: released on January 20, 2015
Fixed pocket zigzag toolpath with islands formed by small circles
Fixed some small bugs
- 2.3.7.0: released on September 22, 2014
Fixed "List index out of bounds" in Drill Cycle with wrong points definition
Fixed some G2/G3 repeated and unnecessary
Fixed some small bugs
- 2.3.4.0: released on May 30, 2014
Fixed the lack of G1 after G2/G3, in very small movements
Fixed some small bugs
- 2.3.1.0: released on December 26, 2013
Fixed wrong toolpath with arcs mirrored or scaled
Fixed writing toolpath comment of Operation Manager
Fixed some small bugs
- 2.3.0.0: released on January 21, 2013
Fixed breaking up in segments of the toolpath with arcs
Added arcs filtering in vectorize process
Fixed writing not required GCode in postprocessing
Fixed some small bugs
- 2.2.0.0: released on December 11, 2012
Fixed casual writing of arcs in the contour toolpath
Fixed reading dxf spline (Settings, Max curve segments)
Added Holding Tabs in contour toolpath
Fixed some small bugs
- 2.1.0.0: released on August 30, 2012
Added Undo function...Hurray!
Fixed the cycles written in some posprocessors
Added the Arc/Circle with 3 points
Fixed Fillet, Trim, Break, Split, Joint and Extend function
Fixed some small NC bugs
- 2.0.5.34: released on June 03, 2012
Fixed simulation in the Nc Editor
Added the ability to interrupt the toolpath calculation
Fixed some small bugs
- 2.0.5.21: released on May 22, 2012
Added 2d/3d simulation in the Nc Editor
Fixed contour cw/ccw direction
- 2.0.1.0: released on May 01, 2012
- 1.8.0.0: released on October 11, 2011
Fixed closed contour with very small entities
Fixed "Access violation at..." in vector font insert
Fixed some command after drill cycle
Fixed move origin in Dxf open
- 1.75.00: released on June 21, 2011
Added 7 new fonts Single Line
Fixed the "The application failed ...." on points selection for drill cycle
- 1.73.00: released on December 29, 2010
Updated OpenGL compatibility
Fixed memory deallocations
- 1.72.00: released on December 14, 2010
Fixed to read Dxf files created with Autocad 2010/2011
Fixed memory deallocations with Pocket function
- 1.71.00: released on September 26, 2010
Fixed the " The application failed ...." on some computers
Fixed reading closing lwpolyline entities
- 1.70.00: released on September 18, 2010
Added Single Line fonts management
Fixed pocket with polyline/spline entities
- 1.59.30: released on July 13, 2010
Added Polish language
Added function to create holes along entity
Fixed reading closed arcs
Fixed some small bugs
- 1.59.20: released on March 31, 2010
Windows 7 Compatibility Fix
Fixed crash in font creation
Fixed wrong toolpath display with R word
Added Spanish language
- 1.59.10: released on October 2, 2009
Fixed chain bug in Drill function
- 1.59.00: released on September 1, 2009
Fixed memory deallocations
Fixed contour/pocket with small entities
Fixed circle pocket
Fixed arrow in toolpath direction
Added Level priority in chain All
Added Remove all chain command
- 1.57.30: released on March 18, 2009
Fixed chaining function
- 1.57.00: released on September 12, 2008
Fixed reading lwpolyline entities with bulge
Fixed some wrong cutting in pocket with island
- 1.56.00: released on May 08, 2008
Fixed 'list out bond' message
Added new vars in .pst file
- 1.55.00: released on March 08, 2008
Added estimate machining time
Added German language
Fixed reading polyline with bulge
- 1.53.00: released on February 13, 2008
Fixed reading Dxf file without header section
- 1.51.00: released on September 26, 2007
Fixed some bugs
- 1.50.00: released on September 10, 2007
Added Contour toolpath with cutter compensation
Added Pocket toolpath
Modified the profile selection
Added Join and Split function
Added "2d solid" simulation
- 1.27.03: released on June 4, 2006
Added and fixed some postprocessor
Fixed Dxf Block read
- 1.27.00: released on September 27, 2006
Added Point grid and Point bolt circle
Added Move/Copy operations in Translate, Rotate, Mirror and Scale functions
Modified the use of Xform functions
Added Distance functions
Fixed Dxf v2004 read
- 1.26.02: released on August 28, 2006
Added Line tangent 2 arcs, line tangent angle
Added Line polar, Line perpendicular, Arc Tangent
Added arc extension
Fixed rare problem to write temp files.
- 1.25.11: released on August 05, 2006
Improved stability
Added 3d simulation
Fixed drill simulation
- 1.25.03: released on July 22, 2006
Added support to external language file
Fixed peckdrill routine
- 1.25.02: released on July 16, 2006
Fixed explode block function
Fixed inch conversion
- 1.25.00 was released on Juny 30, 2006