Download SimplyCam, SimplyLaser, SimplyLathe versione Trial

 Note:

  • Scaricare la versione trial dal link sottostante o se utente registrato eseguire l'accesso alla Customer Area e scaricare la versione completa.
  • Gli utenti registrati, saranno avvisati via email, del rilascio di nuovi aggiornamenti significativi.
  • Limitazioni della versione di prova:
    Non salva in formato Dxf.
    Genera max 100 righe di programma G-Code
SimplyCam download

SimplyCam v3.66 versione Trial

(Nota: il programma Nc generato è troncato a circa 100 righe)

Questa versione è attualmente in fase di sviluppo. Verificare con regolarità la presenza di nuove versioni.

Per installare il programma, scaricare e decomprimere il file SimplyCam3.zip in una directory temporanea.
Usare Winzip o un'altra recente utility di decompressione.
Eseguire "setup-simplycam3.exe" per iniziare il processo di installazione.

SimplyCam download

SimplyLaser v3.66 versione Trial

(Nota: il programma Nc generato è troncato a circa 100 righe)

Questa versione è attualmente in fase di sviluppo. Verificare con regolarità la presenza di nuove versioni.

Per installare il programma, scaricare e decomprimere il file SimplyLaser3.zip in una directory temporanea.
Usare Winzip o un'altra recente utility di decompressione.
Eseguire "setup-simplylaser3.exe" per iniziare il processo di installazione.

SimplyCam download

SimplyLathe  v3.49 versione Trial

(Nota: il programma Nc generato è troncato a circa 100 righe)

Nota: Nessun ulteriore sviluppo. Il modulo SimplyLathe non sarà più aggiornato e supportato.

Per installare il programma, scaricare e decomprimere il file SimplyLathe3.zip in una directory temporanea.
Usare Winzip o un'altra recente utility di decompressione.
Eseguire "setup-simplylathe3.exe" per iniziare il processo di installazione.

SimplyCam Help

File di Help da installare in locale, se il computer su cui è installato SimplyCam non dispone di una connessione Internet.
Aggiornato alla versione 3.0.5 il 26/07/2015.

Cliccare qui, per iniziare il download del file di Help di SimplyCam3 - (2.5 Mb)

SimplyCam,lista delle versioni
Per ottenere l'esatta versione dell'applicazione SimplyCam installata sul Vs computer, selezionare About dal menu Help.

  • 3.6.6.3: released on February 01, 2020
    Fixed many small bugs
  • 3.6.6.0: released on January 24, 2020
    Fixed many small bugs
  • 3.6.5.0: released on November 05, 2019
    Fixed many small bugs
  • 3.6.0.0: released on July 30, 2019
    Added Merge Snc file
    Added Retract Plane in mill toolpaths
    Fixed pocket toolpath
    Fixed postprocessor vars
    Fixed many small bugs
  • 3.5.0.0: released on November 15, 2018
    Fixed many small bugs
  • 3.4.9.0: released on May 15, 2018
    Fixed many small bugs
  • 3.4.0.0: released on November 15, 2017
    Fixed Svg parsing
    Fixed some small bugs
  • 3.3.9.0: released on September 06, 2017
    Added toolpath to Geo/Dxf funcion
    Added Comments operations
    Fixed Write operation in Laser module
    Fixed some small bugs
  • 3.3.8.0: released on July 19, 2017
    Added Laser Pocket toolpath
    Fixed some small bugs
  • 3.3.6.0: released on February 14, 2017
    Fixed some small bugs
  • 3.3.5.0: released on January 22, 2017
    Fixed dxf read lwpolyline
    Fixed some small bugs
  • 3.3.0.0: released on July 16, 2016
    Added Write toolpath
    Fixed some small bugs
  • 3.2.0.0: released on April 19, 2016
    Added GRBL Panel
    Added Solid Simulator
    Separate module management Mill, Laser, Lathe
    Added TrueType UTF8 management
    Added line-width of toolpath
    Fixed zig zag Pocket toolpath
    Fixed Drag/Drop operations
    Fixed crash on Simulation
    Fixed some small bugs
  • 3.0.6.0: released on August 08, 2015
    Fixed open Contour toolpath
    Fixed crash on Simulation
    Fixed some small bugs
  • 3.0.5.0: released on July 26, 2015
    Added Help
    Fixed Lathe Finish toolpath
    Fixed some small bugs
  • 3.0.3.0: released on June 19, 2015
    Added Lathe Rough and Lathe Finish toolpath
    Fixed Vectorize function
    Fixed editing entities in Treeview
    Fixed some small bugs
  • 3.0.1.0: released on April 07, 2015
  • 2.4.0.0: released on January 20, 2015
    Fixed pocket zigzag toolpath with islands formed by small circles
    Fixed some small bugs
  • 2.3.7.0: released on September 22, 2014
    Fixed "List index out of bounds" in Drill Cycle with wrong points definition
    Fixed some G2/G3 repeated and unnecessary
    Fixed some small bugs
  • 2.3.4.0: released on May 30, 2014
    Fixed the lack of G1 after G2/G3, in very small movements
    Fixed some small bugs
  • 2.3.1.0: released on December 26, 2013
    Fixed wrong toolpath with arcs mirrored or scaled
    Fixed writing toolpath comment of Operation Manager
    Fixed some small bugs
  • 2.3.0.0: released on January 21, 2013
    Fixed breaking up in segments of the toolpath with arcs
    Added arcs filtering in vectorize process
    Fixed writing not required GCode in postprocessing
    Fixed some small bugs
  • 2.2.0.0: released on December 11, 2012
    Fixed casual writing of arcs in the contour toolpath
    Fixed reading dxf spline (Settings, Max curve segments)
    Added Holding Tabs in contour toolpath
    Fixed some small bugs
  • 2.1.0.0: released on August 30, 2012
    Added Undo function...Hurray!
    Fixed the cycles written in some posprocessors
    Added the Arc/Circle with 3 points
    Fixed Fillet, Trim, Break, Split, Joint and Extend function
    Fixed some small NC bugs
  • 2.0.5.34: released on June 03, 2012
    Fixed simulation in the Nc Editor
    Added the ability to interrupt the toolpath calculation
    Fixed some small bugs
  • 2.0.5.21: released on May 22, 2012
    Added 2d/3d simulation in the Nc Editor
    Fixed contour cw/ccw direction
  • 2.0.1.0: released on May 01, 2012
  • 1.8.0.0: released on October 11, 2011
    Fixed closed contour with very small entities
    Fixed "Access violation at..." in vector font insert
    Fixed some command after drill cycle
    Fixed move origin in Dxf open
  • 1.75.00: released on June 21, 2011
    Added 7 new fonts Single Line
    Fixed the "The application failed ...." on points selection for drill cycle
  • 1.73.00: released on December 29, 2010
    Updated OpenGL compatibility
    Fixed memory deallocations
  • 1.72.00: released on December 14, 2010
    Fixed to read Dxf files created with Autocad 2010/2011
    Fixed memory deallocations with Pocket function
  • 1.71.00: released on September 26, 2010
    Fixed the " The application failed ...." on some computers
    Fixed reading closing lwpolyline entities
  • 1.70.00: released on September 18, 2010
    Added Single Line fonts management
    Fixed pocket with polyline/spline entities
  • 1.59.30: released on July 13, 2010
    Added Polish language
    Added function to create holes along entity
    Fixed reading closed arcs
    Fixed some small bugs
  • 1.59.20: released on March 31, 2010
    Windows 7 Compatibility Fix
    Fixed crash in font creation
    Fixed wrong toolpath display with R word
    Added Spanish language
  • 1.59.10: released on October 2, 2009
    Fixed chain bug in Drill function
  • 1.59.00: released on September 1, 2009
    Fixed memory deallocations
    Fixed contour/pocket with small entities
    Fixed circle pocket
    Fixed arrow in toolpath direction
    Added Level priority in chain All
    Added Remove all chain command
  • 1.57.30: released on March 18, 2009
    Fixed chaining function
  • 1.57.00: released on September 12, 2008
    Fixed reading lwpolyline entities with bulge
    Fixed some wrong cutting in pocket with island
  • 1.56.00: released on May 08, 2008
    Fixed 'list out bond' message
    Added new vars in .pst file
  • 1.55.00: released on March 08, 2008
    Added estimate machining time
    Added German language
    Fixed reading polyline with bulge
  • 1.53.00: released on February 13, 2008
    Fixed reading Dxf file without header section
  • 1.51.00: released on September 26, 2007
    Fixed some bugs
  • 1.50.00: released on September 10, 2007
    Added Contour toolpath with cutter compensation
    Added Pocket toolpath
    Modified the profile selection
    Added Join and Split function
    Added "2d solid" simulation
  • 1.27.03: released on June 4, 2007
    Added and fixed some postprocessor
    Fixed Dxf Block read
  • 1.27.00: released on September 27, 2006
    Added Point grid and Point bolt circle
    Added Move/Copy operations in Translate, Rotate, Mirror and Scale functions
    Modified the use of Xform functions
    Added Distance functions
    Fixed Dxf v2004 read
  • 1.26.02: released on August 28, 2006
    Added Line tangent 2 arcs, line tangent angle
    Added Line polar, Line perpendicular, Arc Tangent
    Added arc extension
    Fixed rare problem to write temp files.
  • 1.25.11: released on August 05, 2006
    Improved stability
    Added 3d simulation
    Fixed drill simulation
  • 1.25.03: released on July 22, 2006
    Added support to external language file
    Fixed peckdrill routine
  • 1.25.02: released on July 16, 2006
    Fixed explode block function
    Fixed inch conversion
  • 1.25.00 was released on Juny 30, 2006

Copyright © 2006-2024 MR-Soft. All rights reserved.